變速箱維修后是否會有什么影響？維修后有影響，只有兩點至關重要的原因，一個是維修人員的技術水平不夠穩，工作不夠仔細，二就是配件問題。濟南自動變速箱維修廠家建議可以把這兩點分為四點來說。

Is there any impact after the gearbox is repaired? There are only two important reasons for the impact after maintenance. One is that the technical level of the maintenance personnel is not stable enough and the work is not careful enough. The other is the problem of parts. Jinan automatic transmission maintenance manufacturer suggested that these two points can be divided into four points.

一，維修技師在維修前是否能準確判斷故障點。

1、 Whether the maintenance technician can accurately judge the fault point before maintenance.

一個經驗豐富的維修技師，通過檢查故障代碼，試車或是車主的口述，即可快速的說出具體的故障點，這樣的話，在維修時候就沒有了盲點，拆卸時候只需要更換損壞配件，再認真檢查其他沒有故障的配件，做好防御工作即可了。而如果沒有及時判斷出故障點的話，在拆掉時候就會很迷茫，逐一排查，很浪費時間經歷，到后即使換了一圈配件，也不見得會修好。

An experienced maintenance technician can quickly tell the specific fault point by checking the fault code, test run or the dictation of the owner. In this way, there is no blind spot during maintenance. During disassembly, only damaged parts need to be replaced, and other parts without fault should be carefully checked to do a good job of defense. If the fault point is not determined in time, it will be very confused when removing it. It is a waste of time and experience to check one by one. Even if a circle of parts is replaced, it is unlikely that they will be repaired.

二，維修技師在維修時候有沒有認真判斷好損壞的主要原因和間接原因。

2、 Did the maintenance technician carefully judge the main and indirect causes of the damage during maintenance.

某款變速箱本身是十分容易出現頭殼漏油的故障的，正常的思維都是更換油封就行了，其實除了油封之外，還有很多造成漏油的間接原因。就比方說是定位環，限位墊片。原車的定位環是橡膠材質的，很容易出現老化變稀的情況，改進的為剛性定位環，可以避免故障。而限位墊片是表面磨光了，改進的限位墊片做了加長，表面還有耐磨層，延長使用壽命。

The gearbox itself is prone to oil leakage from the head case. The normal thinking is to replace the oil seal. In fact, in addition to the oil seal, there are many indirect causes of oil leakage. For example, it is a locating ring and a limiting gasket. The locating ring of the original vehicle is made of rubber, which is prone to aging and thinning. The improved rigid locating ring can avoid failure. The surface of the limit gasket is polished, and the improved limit gasket is lengthened. There is also a wear-resistant layer on the surface, extending the service life.

三，配件是否改進。

3、 Whether the parts have been improved.

有些變速箱是比較容易出現緩沖片故障的。緩沖片材質太薄承受不住變速箱內部常年高溫，造成的燒蝕斷裂現象，面對于這個情況，很多人會選擇更換原廠的緩沖片，其實這個目前是有改進的加寬加厚的緩沖片了，改進的除了加寬加厚這個優點之外，表面還加上了激光打印的耐磨層，更為耐磨一些。緩沖片對比，改進的明顯加寬加厚，原車的只有薄薄的一層。

Some transmissions are prone to buffer failure. The material of the buffer plate is too thin to withstand the perennial high temperature inside the gearbox, resulting in ablation and fracture. Faced with this situation, many people will choose to replace the original buffer plate. In fact, there is an improved widened and thickened buffer plate. In addition to the advantage of widening and thickening, the surface of the improved buffer plate is also equipped with a laser printed wear-resistant layer, which is more wear-resistant. Compared with the buffer plate, the improved one is obviously widened and thickened. The original one has only a thin layer.

四，維修技師是否認真安裝。

4、 Whether the maintenance technician carefully installs.

在安裝配件時候，如果沒有認真的安裝，擰緊螺絲的話，也是很容易出現后期的故障。所以，在保證配件全部安裝的情況下，還要保證好配件的安裝程度，有沒有松的地方，這一點也是會在維修后，出現故障的。總之，選擇做事認真，仔細、為您省錢的維修廠，還是至關重要的一點的。

When installing accessories, if you do not carefully install and tighten the screws, it is also easy to have late failures. Therefore, under the premise of ensuring that all the accessories are installed, it is also necessary to ensure the installation degree of the accessories and whether there is any looseness. This will also cause failures after maintenance. In a word, it is very important to choose a repair shop that is conscientious, careful and saves you money.

變速箱維修后，要想沒有什么影響和故障，那就先注意好維修時候，先了解好愛車裝配的變速箱，是否有改進配件，找維修技師判斷好問題，裝配件時候也要讓維修技師保證好每個配件的嚴實性，避免后期故障。更多相關內容就來我們這里http://m.566605.com咨詢吧！

After the gearbox is repaired, if there is no impact or fault, pay attention to the maintenance first, understand the gearbox fitted to your car and whether there are any improved parts, find a maintenance technician to judge the problem, and ask the maintenance technician to ensure the tightness of each part when assembling the parts, so as to avoid future faults. Come here for more information http://m.566605.com Consult!